Fenix E18R V2.0 GE rechargeable flashlight, nebula

This description was machine translated from the original text.

Fenix E18R V2.0 is a rechargeable miniature pocket LED flashlight with a short-term extreme output of up to 1200 lumens (ANSI). This model uses a top-of-the-line Luminus SST-40 diode as a light source. Thanks to the length of only 67 millimeters and the weight of 56 grams (including the battery), it can be carried with you at all times - in your pocket, on your keys or in your purse. It is powered by a rechargeable Li-ion battery RCR123A, which can be charged in the lamp via the USB-C connector from any USB source (e.g. computer, power bank, USB source in the car). A disposable CR123A battery can also be used in an emergency.

It goes without saying that the high quality of the design, durability and waterproofness are essential. The lamp is equipped with a removable clip and the end is magnetic. A unique innovation is a special collimator that creates a light cone with a surprising afterglow of 146 meters . The collimator is made with technology used in the automotive industry and its height is only 3 millimeters , which is less than half compared to commonly used optics. Due to its characteristics, the lamp is destined to serve as an ideal small, reliable companion that is always at hand. If this flashlight is a gift, it will always make you happy.

All lamp parameters (luminous flux, battery operation time, waterproofing, afterglow and impact resistance) are measured in accordance with the ANSI/NEMA FL 1-2009 standard.

Fenix E18R V2.0 lamp parameters

• A premium powerful Luminus SST-40 LED with a lifespan of 50,000 hours is used.

• Six power modes: 1200 lumens (30 minutes) -> 350 lumens (1.3 hours) -> 150 lumens (2.5 hours) -> 30 lumens (15 hours) -> 1 lumen ( 200 hours ) -> strobe ( 1200 lumens)

• Endurance times are measured with the included Fenix ARB-L16-700P Li-ion battery with a capacity of 700 mAh.
• The operation of the highest mode is limited to avoid damage to the lamp. If the internal temperature reaches 60°C, the performance will be reduced automatically.
• Digitally regulated for constant brightness.
• It uses one rechargeable Li-ion battery 3.7 V RCR123A/16340 for power, which can be recharged in the lamp via the USB-C connector.
• The charging time of a completely discharged battery is approximately 80 minutes.
• In an emergency, it is possible to use a CR123A disposable battery (it cannot be charged in the lamp and the maximum power will be lower).
• Protection against accidentally inserting the battery upside down (reverse polarity).
• The lamp has a memory and will always turn on in the last set mode (does not apply to the highest mode and stroboscope).
• A special super-thin collimator only 3 mm high, made with technology used in the automotive industry.
• Magnetic end, can be attached to anything iron.
• Light cone with an afterglow of up to 146 meters (5397 cd).
• Dimensions 6.7 cm (length) x 2.2 cm (body diameter) x 2.2 cm (reflector diameter).
• Weight 56 grams (including battery).
• Made of aviation hardened aluminum type A6061-T6, durable surface - Type III hard anodized.
• Impact-resistant from a fall from a height of 1 meter.
• Dustproof and waterproof according to the IP68 standard (tested under water at a depth of 2 meters).
• Able to stand on its own on a flat place and serve as a candle.
• The package includes a Fenix ARB-L16-700P battery, a USB-C charging cable, a metal ring for hanging on keys, a loop and a spare sealing o-ring.
• As optional accessories, it is possible to purchase, for example, the AOD-S V2.0 diffuser (to attach it, you need to remove the clip from the flashlight; the diffuser then covers the button), ALW-01 rotating wrist holder, LampFix helmet holder, LockBlocks bicycle holder, silicone holder, USB adapter for the mains and USB adapter for the car or a spare battery RCR123A with a micro-USB connector or a spare battery with a higher capacity of 800 mAh.

Usage

To turn on or off, hold down the side button for about 0.5 seconds. You can switch power modes at any time during operation by pressing the side button. To switch to flash mode, hold down the side button for about 1.2 seconds.

The control button can be locked so that it does not turn on by itself, e.g. when transported in luggage - press the control button twice quickly (within 0.5 seconds). To unlock, quickly press the button twice again.

Intelligent protection against overheating - due to the fact that such a small lamp reaches such an extreme output of 1200 lumens, it heats up. If the temperature exceeds 60°C, the power will be automatically reduced. As soon as the temperature drops below 60 °C, the highest power can be used again.

Charging - unfold the rubber cover of the charging connector on the side of the lamp and plug in the enclosed cable (USB-C connector), plug the other end of the cable into the computer or the USB adapter into the electrical network or car. During charging, the indicator LED flashes red weakly. It lights up green when fully charged. Charging a fully discharged battery takes about 1 hour and 20 minutes.

Battery charge status indication - when the lamp is off, a short press of the side button activates the indicator LED in the side button of the lamp for three seconds. If the indicator light is green, the battery is charged to more than 85%. Green flashing means 50-85% capacity. If it lights up red, it is charged to 25-50%. Blinking red means less than 25% of battery capacity remains.

Warning of exhausted batteries (functional only when using Li-ion RCR123A) - the lamp will gradually automatically switch to the lowest mode and the indicator LED in the button will start flashing red.

Warning

• Do not disassemble the sealed part in the lamp head yourself, this will void the warranty.
• Use only high-quality 3V CR123A batteries and RCR123A Li-ion batteries to avoid damage to the lamp, for example due to leakage of substances from the battery.
• If the protective rubber rings appear damaged after a long period of use, replace them. The rings must also be lubricated to prevent rubber erosion. By following these rules, the lamp will be properly protected against water.
• If the light flickers, does not switch to higher power modes, or does not light up, it may be for one of the following reasons:
  • The battery is dead - charge it.
  • The contacts inside the lamp are dirty - clean them with a cotton swab dipped in alcohol.
  • The lamp body is loose, tighten it.